通過式噴淋清洗機洗不干凈可能有以下幾個原因：

　　There may be several reasons why the through spray cleaning machine cannot clean thoroughly:

　　水壓問題 ：

　　Water pressure issue:

　　如果水壓過低，噴淋力度不夠，無法有效沖刷餐具表面的污垢。

　　If the water pressure is too low and the spraying force is not sufficient, it will not be able to effectively wash away the dirt on the surface of the tableware.

　　檢查水龍頭的水壓是否正常，并確保水管沒有堵塞。

　　Check if the water pressure of the faucet is normal and ensure that the water pipe is not blocked.

　　餐具擺放錯誤 ：

　　Dishware placement error:

　　餐具擺放得過于擁擠或者相互覆蓋，噴淋系統無法充分覆蓋到每個餐具表面。

　　The tableware is placed too crowded or covered with each other, and the sprinkler system cannot fully cover the surface of each tableware.

　　確保每個餐具之間留有足夠空間，以便水可以噴灑到所有餐具表面。

　　Ensure that there is enough space between each utensil so that water can spray onto all utensil surfaces.

　　洗滌劑問題 ：

　　Detergent issue:

　　使用洗滌劑量不足或者質量不佳，無法有效分解油脂和污垢。

　　Insufficient detergent dosage or poor quality cannot effectively decompose oil and dirt.

　　選擇質量可靠的產品，并按照說明書的要求使用適量的洗滌劑。

　　Choose products with reliable quality and use an appropriate amount of detergent according to the instructions.

　　噴淋系統問題 ：

　　Spray system issues:

　　噴淋臂轉動不順暢，可能是有餐具阻礙噴淋臂的正常轉動，或者噴淋臂上的噴水孔被堵塞。

　　The spray arm is not rotating smoothly, which may be due to tableware obstructing the normal rotation of the spray arm, or the spray hole on the spray arm being blocked.

　　檢查噴淋臂旋轉是否正常，噴射臂上小孔是否堵塞，噴射臂軸是否有磨損或脫落。

　　Check if the spray arm rotates normally, if the small holes on the spray arm are blocked, and if the spray arm shaft is worn or detached.

　　加熱和過濾問題 ：

　　Heating and filtering issues:

　　如果加熱器冷凝水沒有順利排出或水垢積聚，可能會導致清洗液溫度上升緩慢。

　　If the condensed water from the heater is not discharged smoothly or scale accumulates, it may cause the temperature of the cleaning solution to rise slowly.

　　過濾器雜物積聚未及時清洗，阻力較大，也會影響清洗效果。

　　The accumulation of impurities in the filter and failure to clean it in a timely manner can cause significant resistance and also affect the cleaning effect.

　　水質問題 ：

　　Water quality issues:

　　使用的水源如果不符合要求（如軟化水或純水標準），可能會導致器械上有白斑或殘留物。

　　If the water source used does not meet the requirements (such as softened water or pure water standards), it may cause white spots or residues on the equipment.

　　確保使用的水源為軟化水或純水，并且電導率符合要求。

　　Ensure that the water source used is softened water or pure water, and that the conductivity meets the requirements.

　　其他故障 ：

　　Other faults:

　　檢查循環泵是否有翻轉現象，循環管路是否有泄漏，管卡是否松動。

　　Check if there is any flipping phenomenon in the circulation pump, if there is any leakage in the circulation pipeline, and if the pipe clamp is loose.

　　清洗架噴射臂旋轉是否正常也需要檢查。

　　It is also necessary to check whether the spray arm of the cleaning rack rotates normally.

　　針對以上可能的原因，可以逐一排查并解決，以提高通過式噴淋清洗機的清洗效果

　　For the possible reasons mentioned above, they can be investigated and resolved one by one to improve the cleaning effect of the through type spray cleaning machine

　　本文由通過式噴淋清洗機提供技術支持，更多的詳細精彩內容請點擊我們的網站http://m.best80.cn，我們將會全心全意為您提供滿意的服務。

　　This article is supported by a through type spray cleaning machine. For more detailed and exciting content, please click on our website http://m.best80.cn We will wholeheartedly provide you with satisfactory service.